Posted on: January 20, 2020 Posted by: admin Comments: 0


American Audio | V | User manual | American Audio V User manual American Audio® – – V Vplus Series Amplifiers Power. American audio V PLUS Pdf User Manuals. View online or download American audio V PLUS User Instructions. View and Download American Audio V/V user instructions online. PROFESSIONAL POWER AMPLIFIERS. V/V Amplifier pdf manual.

Author: Vimi Dijas
Country: Burkina Faso
Language: English (Spanish)
Genre: Literature
Published (Last): 2 December 2017
Pages: 27
PDF File Size: 19.39 Mb
ePub File Size: 4.54 Mb
ISBN: 689-6-13985-445-1
Downloads: 19109
Price: Free* [*Free Regsitration Required]
Uploader: Kazirg

Ensuring proper polarity will avoid speakers being out of phase, that can cause a loss of bass response. The limiter reduces the average output level when the signal begins to distort, xmerican process is designed to reduce distortion and protect the speakers.

Connecting to the wrong voltage is dangerous and may damage the amplifier.

American Audio V User manual |

This LED may glow when the unit has been turned off, this is normal. Americaan Plugs – When connecting your speakers to the amplifier using banana b3000 Be sure that the red and black caps on the binding post are completely screwed in.

A limiter takes the gain of an overloading signal and reduces it, the reduction in gain reduces distortion that can cause damage to your speakers and amplifier. The appliance has been exposed to rain or water. Be sure not to raise the volume to the clip level, however an intermittent clip signal is acceptable.

These fans are used to cool the internal parts of the amplifier. No hay piezas adentro que el usario puede reparar. To reduce the risk of electrical shock, do a,erican remove cover. If it is lit about half the time, the amplifier channel will probably go into thermal protection within a few minutes.


If this line good, check the internal speaker connections and components. Short Circuit Protection can usually be traced back to the signal output line i.

Thermal Protection – A single variable-speed fan on the V Vplus and dual variable speed fans on the V Vplus and V Vplus amplifiers provide adequate cooling.

American Audio V3000 PLUS Manuals

If your speaker lines short, the amplifier automatically detects this problem and discontinues operation for that channel. If the input gain level is not reduced the built-in limiter will activate.

Typical speaker output using bare wire. Channel 1 Frequency Adjustment. Enter text from picture: These amplifiers are designed to provide a big impact in sound reproduction.

This light may continue to glow briefly after main power has been turned off, this is normal. Low Cut Filter V and V Only – The low-cut filter removes extremely low frequencies from the audio signal that could cause speaker distortion or damage. Specifications rated output power,8 ohms Cooling System: Inputs 50 Hz filter setting if you are using the amplifier to drive a distributed line system also known as a constant-voltage line, 70 volt line, etc.

The speaker wire may be connect by bare wire directly connected, usually for permanent connectionsbanana plug, or spade connector. See limiter page Bridged-Mono Mode Caution – The voltage across the output terminals of a bridged V Vplus series amplifier may equal or exceed volts RMS and may be as high as volts. For cable runs shorter than 20ft.

Amplifiers are shipped in stereo mode.

American Audio › V › Amplifier – Gearbase | DJResource

Got it, continue to print. To reduce the risk of shock or damage to your amplifier, be sure that the wire connected to one binding post does not come in contact with audik of another.


The front panel provides four holes used to screw the unit into a rack. Don’t show me this message again. Be sure that your front gain controls are turned down to their lowest level full counter-clockwise. Rear mounting the unit is especially recommended if the aamerican is to mounted into a mobile rack.

Although a speaker will operate with the positive and negative leads plugged into either terminal on the amplifier binding post, be sure to plug the negative lead into the black terminal and positive lead into V300 8 the red terminal.

You may also visit us on the web at www. Cooling Fan – This is a dual speed cooling fan. Connecting to the wrong voltage is dangerous and may damage the amplifier. Use the channel one gain to regulate your amplifier output. When the input signal decreases enough that clipping ends, the limiter will deactivate and cease its gain reduction. When constructing your own XLR cables follow the pin configuration describe below for proper connections.

Cooling Fan Dual speed cooling fans. Connect your inputs into channels one and two of the amplifier. During low level output the fans run at normal speeds.


Leave a Comment