iso – Download as PDF File .pdf), Text File .txt) or read online. Safety of Machinery Documents Similar To iso Bs en Iso – Part 2. EN ISO and EN ISO are Type A standards (basic safety standards) and therefore have a dual purpose: they are. BRITISH STANDARD BS EN ISO Incorporating Corrigendum No. 1 Safety of machinery — Basic concepts, general principles for.
|Published (Last):||18 October 2015|
|PDF File Size:||3.86 Mb|
|ePub File Size:||2.83 Mb|
|Price:||Free* [*Free Regsitration Required]|
You may experience issues viewing this site in Internet Explorer 9, 10 or Information for use a? Cycle initiation by sensitive protective equipment shall be subject to the following conditions: NOTE Consultation of the user on that subject is often necessary. Means of access to parts of machinery located at a height shall be provided with collective means of protection against falls e.
Safety-critical components as, e. See IEC as regards marking of electrical equipment.
BS EN ISO _百度文库
When carrying out a risk assessment, the risk from the most likely severity of the harm that is likely to occur from each identified hazard shall be considered, but the highest foreseeable severity shall also be taken into account, even if the probability of such an occurrence is not high. When protective measures include work organization, correct behaviour, attention, application of personal protective equipment PPEskill or training, the relatively low reliability of such measures compared with proven technical protective measures shall be taken into account in the risk estimation.
NOTE 2 Environmental conditions which are to be taken into consideration are, for instance: Except as permitted under the Copyright, Designs and Patents Act no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means — electronic, photocopying, recording or otherwise — without prior written permission from BSI.
On machinery intended for lifting persons, controls for lifting and lowering and, if appropriate, for moving the carrier, shall generally be located in the carrier. The following provisions are intended to provide the designer with criteria for selecting, for each application, the most suitable device s. While automatic feeding and removal devices have much to offer in preventing accidents to machine operators, they can create danger when any faults are being rectified.
The use of such components should always be considered, particularly in cases where redundancy see 6. Once this standard is cited in the Official Journal of the European Union under that Directive and has been implemented as a national standard in at least one Member State, compliance with the normative clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity with the relevant Essential Requirements of that Directive and associated EFTA regulations.
It also provides a strategy for standards developers and will assist in the preparation of consistent and appropriate type-B and type-C standards. Technical principles, giving advice on how this philosophy can be applied using available techniques. Amendments issued since publication Amd. The selector may be replaced by another selection means which restricts the use of certain functions of the machinery to certain categories of operators e.
This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Mayand conflicting national standards shall be withdrawn at the latest by May Typical causes of hazardous machine behaviour are: November Replaced By: Factors to be taken into account when estimating the possibility of avoiding or limiting harm are, among others, the following: In selecting an appropriate safeguard for a particular type of machinery or hazard zone, it shall be borne in mind that a fixed guard is simple and shall be used where access of an operator to the danger zone is not required during normal operation operation without any malfunction of the machinery.
Potential consequencesb discomfort; fatigue; musculoskeletal disorder; stress; any other for example, mechanical, electrical as a consequence of a human error. For example, when a band saw used? They should not be separated from the accompanying text and should follow sequential operations.
Safety of machinery: EN ISO 12100-1 and EN ISO 12100-2
The information for use shall include, but not be limited to, the following: Types of sensitive protective equipment include? The primary action for stopping or slowing down should be performed by removal or reduction of voltage or fluid pressure, or — if binary logic elements are considered — by passage from state 1 to state 0 where state 1 represents the highest energy state.
A combination of safeguards izo sometimes be required. As part of this iterative process, the designer shall also check whether additional hazards are introduced or other risks increased when new protective measures are applied.
It is incorporated by Royal Charter. Risk analysis YES Risk evaluation see 5. Consideration should be given to presenting information in tabular form where this will aid understanding.
We would be grateful if anyone finding an inaccuracy or ambiguity while using this 121000-2 Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. It also provides a strategy for standard makers. When estimating risk, those components and systems identified as immediately increasing the risk in case of failure need special attention.
At least the following requirements shall be met: Contact the Information Centre. Factors to be taken into account when estimating the occurrence of a hazardous event are, among others, a b c d reliability and other statistical data, accident history, history of damage to health, and comparison of risks see 5.
When the application requires reprogramming by the user, the access to the software dealing with safety functions should be restricted e. Terminology and general principles  ENSafety of machinery — Ergonomics requirements for the design of displays and control actuators — Part 3: All reasonably foreseeable hazards, hazardous situations or hazardous events associated with the various tasks shall then be identified. Both parts of EN ISO also recommend that the standard be incorporated in training courses and manuals to ‘convey basic terminology and general design methods to designers.