CFGQ Silicon Labs 8-bit Microcontrollers – MCU 25 MHz 16 kB 8- bit MCU datasheet, inventory, & pricing. Explore the latest datasheets, compare past datasheet revisions, and confirm part lifecycle. CF datasheet, CF pdf, CF data sheet, datasheet, data sheet, pdf, Silicon Laboratories, Full Speed USB, 16k ISP FLASH MCU Family.
|Published (Last):||14 August 2011|
|PDF File Size:||9.31 Mb|
|ePub File Size:||14.81 Mb|
|Price:||Free* [*Free Regsitration Required]|
This bit sets the priority of the SPI0 interrupt.
Download datasheet 2Mb Share this page. Either direct or indirect addressing may be used to access the lower bytes of data memory.
C8051F320 Datasheet PDF
MUX Select Figure 5. Locking any Flash page also locks the page containing the Lock Byte.
This bit does not indicate the instantaneous. This mode is available for Endpoints This bit controls the SPI0 clock polarity.
The write and erase operations are automatically timed by hardware for proper execution In this mode, the maximum packet size is halved and the FIFO may contain two packets at a time. Can I use daughter card to connect to a peripheral on the motherboard via any type of connection?
Used by SJMP and all conditional jumps. In terms of hardware peripherals, only a comparator and timer are required, which leaves many resources available for the rest of the system. Serial Port 0 Control. Prev Next Analog Peripherals.
So I fired up eagle and designed a breakout board for this chip and in 4 hours I had the board ready to be used. This bit sets the priority of the Timer 3 interrupt. Refer to the datasheet section associated with a particular on-chip peripheral for datasheer regarding valid interrupt conditions for the peripheral and the behavior of its interrupt-pending flag s Refer to the datasheet section associated with a particular on-chip peripheral for information regarding valid interrupt conditions for the peripheral darasheet the behavior of its interrupt-pending flag s.
forum • View topic – Silabs CF Breakout Board
Silicon Labs Capacitive Touch Sense Touch sensitive switches are found in a variety of consumer products including home appliances, MP3 players and cell phones. The minimum input voltage is 2. Touch sensitive switches are found in a variety of consumer products including home appliances, MP3 players and cell phones.
This bit will be set to logic 1 when the receive buffer has been read and contains no new information. Last reset was not a USB reset; Write: Post as a guest Name. Setting this bit will place the CIP in Stop mode.
This bit is set by hardware under the conditions listed in Table Seems very cool though, it having a temperature sensor in the ic, full USB with no external clocks, and that is a very beefy regulator! D— signal currently at logic 0.
Instruction and CPU Timing SFR Bus Figure General Purpose Flags 5—0. The number in the switches column indicates the maximum number of switches the can be directly interfaced by the MCU.
CF Datasheet(PDF) – List of Unclassifed Manufacturers
Comparator0 rising-edge interrupt disabled. Locked when any other Flash pages are locked Access limit set according to the Flash security lock satasheet Figure This bit selects the Voltage Regulator mode. Operate in slave mode. The capacitor should be no greater than pF; however for very small capacitors, the total capacitance may be dominated by parasitic capacitance in the PCB layout.
Full Speed USB, 16 K ISP FLASH MCU Family
Flash Write and Erase Guidelines Any system which contains routines which write or erase Flash memory from software involves some risk that the write or erase routines will execute unintentionally if the CPU is operating outside its specified operating range of VDD, system clock frequency, or temperature.
SAR Conversion clock requirements are given in Table The daughter card is pre-loaded with a game that requires you to mimic LED light sequences by entering the sequence via the capacitive touch sense pads. Master Slave Device Device Figure The extended interrupt handler provides 16 interrupt sources into the CIP as opposed to 7 for the stan- dardallowing numerous analog and digital peripherals to interrupt the controller.
A capacitive touch sense solution is easily implemented on many Silicon Labs MCUs and offers many advantages including a low BOM cost, small Flash requirements less than byteslittle MCU overhead, low power requirements and does not require the MCU to use a precise voltage source.