This User’s Manual describes how to use the E5EK compact, high-function digital Nevertheless, OMRON assumes no responsibility for errors or omissions. E5EK-AA Omron Automation and Safety Controllers 1/8 DIN VAC Digital field config datasheet, inventory, & pricing. This product was manufactured at OMRON Okayama. OMRON Okayama has obtained approvals from international certification bodies for its quality system and.
|Published (Last):||26 August 2007|
|PDF File Size:||19.89 Mb|
|ePub File Size:||11.94 Mb|
|Price:||Free* [*Free Regsitration Required]|
However, note that when the set point limiter is reset, the set point is forcibly changed to the upper-or lower-limit value of the set point limiter if the set point is out of the limiter range. Revision History A manual revision code appears as a suffix to the catalog number on moron front cover of the manual. Ensure sufficient space around the control- ler to allow heat radiation. For details on the setting ranges of these parameters, see chapter 5 Level 1 Mode page When replacing the output unit, use the ER.
The following conventions are used to indicate and classify precautions in this manual. Position-proportional Control However, be sure to execute motor calibra- tion after connecting the potentiometer. When the manipulated variable calculated by the E5EK controller is outside of the upper-and lower-limit range, the upper limit Function or lower limit set to these parameters is output, respectively.
Read this chapter only when the controller must be calibrated. In HT hunting tuning mode, when hunting occurs, the PID constants okron amended to suppress the hunting. In an open status, only control output 1 is ON.
PID control, standard con- trol or heating and cooling control. In a close status, only control output 2 is ON.
Omron E5ek-aa2-500 Digital Controller Plug in Cover (cover Only)
Page 15 F Option mode This e5eek the mode for setting option functions. SP tracking function is enabled. Conventions Used omro This Manual J Meanings of Abbreviations Sometimes the following abbreviations are used in parameter names, figures and in text explanations.
Got it, continue to print. Set the control period taking the control characteris- tics and life expectancy of the controller into consideration. To print the manual completely, please, download it. Error 3; RSP input error With control output coolthe conditions for switching from standard control to heating and cooling control are reached when omro output function is assigned at the cooling side during heating and cooling control.
Table of Contents Add to my manuals Add. Page APPENDIX F Startup Conditions of DT 1 DT will start if the temperature that has been stable varies due to external disturbance and the deflection of the temperature exceeds the stable range, e5ei then the temperature becomes stable, pro- vided that the number of maximum temperature values is less than four.
The E5EK controller is calibrated before shipment from the factory. Page 3 Conventions Used in This Manual J Meanings of Abbreviations Sometimes the following abbreviations are used in parameter names, figures and in text explanations. On the E5EK controller, only parameters that can be used are displayed. F Do not cover the area around the E5EK. Read this chapter while referring to the parameter descriptions in chapter 5.
Operating Condition Restrictions The upper limit is set for the heating side positive valueand the lower limit pmron set for the cooling side negative value as shown in the follow- ing figure.
Page 3 Press the key to display [ ] 0mV calibration display. Also, make sure that the power supply is within the rated voltage range.
OMRON E5EK USER MANUAL Pdf Download.
The display changes to [ ] 5 V calibration display. So, 3-position control is made possible. Page level 2 mode.
The heater burnout alarm e5e, always OFF if the alarm is set to 0. Setting Up 2 Draw out the internal mechanism towards you holding both sides of the front panel.
Function Unit Default Setting Range However, if the E5k controller must be calibrated by the user, use the parameters provided for user to calibrate temperature input, analog input voltage, current and transfer output.
You can select this mode only when the option unit is set in the controller. For example, in the fol- lowing configuration, connect the terminator to the host unit and the unit No.
In other words, you cannot switch between the auto and manual operations by key operation. Failure to heed precautions can result in inju- ry to people or damage to the product.