Posted on: January 22, 2020 Posted by: admin Comments: 0

IC HT12E DATASHEET PDF

HT12E is a series encoder IC (Integrated Circuit) for remote control applications. It is commonly used for radio frequency (RF) applications. By using the. HT12E Datasheet, HT12E Holtek Encoder Datasheet, buy HT12E Encoder IC. The capa- bility to select a TE trigger on the HT12E or a. DATA trigger on the HT12A/B/C further en- hances the application flexibility of the 2.

Author: Meztilar Kecage
Country: Cayman Islands
Language: English (Spanish)
Genre: Science
Published (Last): 19 October 2009
Pages: 37
PDF File Size: 2.71 Mb
ePub File Size: 3.11 Mb
ISBN: 142-7-34793-180-4
Downloads: 32823
Price: Free* [*Free Regsitration Required]
Uploader: Mezigar

Supply voltage; 5V 2. These 12 bits are divided into 8 address bits and 4 data bits.

What is Web Browser. This pin has to be connected to Ground 0V to enable the Transmission. So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. Simply put, HT12E converts the parallel inputs into serial output.

It is mainly used in interfacing RF and infrared circuits. Can range from 2. HT12E is an encoder integrated circuit of 2 12 series of encoders. The IC has a built in ht2e. Interface SD Card with Arduino.

As soon as TE returns to high, the encoder output completes its final cycle and then stops. They are paired with 2 12 series of decoders for use in remote control system applications.

These are the 8-bit address bits, which is used to protect your data. The primary function of HT12E is to encode a bit and send it out through the output pin. Arduino based GPS receiver. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc.

  DELL M6300 SERVICE MANUAL PDF

In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. In this image I have made all four data bits as zero lowwhen this is decoded we will get the same kind of bits on the output side of HT12D, similarly we can make any changes on these 4-bits and they will be reflected on the output side of the HT12D decoder IC.

Pull the Transmission Enable pin pin 14 to ground to activate transmission. Connected to the Ground of circuit. Choosing Battery for Robots. We should set the bits in same pattern on Encoder and Decoder IC to pair them. The encoded bit can be obtained from the Dout pin pin Submitted by admin on 30 October This high-density System-in-Package SiP integrates controller, power switches, and support components. HT12E begins a 4-word transmission cycle upon receipt of a transmission enable.

For decoding a data the IC will requires an oscillator, luckily this IC has one in-built. They can also be connected to switches to manually send and receive data.

A basic connection diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting datashee address pins to ground.

This cycle is repeated as long hh12e TE is kept low. HT12E has a transmission enable pin which is active low. The 4-bit data that has to be sent has to be given to the pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7.

  FM31 - 70 PDF

Choosing Motor For Robots. TL — Programmable Reference Voltage.

HT12E Encoder IC

Interface GPS with Arduino. Virgin Galactic — Commercial Space Flight. It is very important that your Decoder should also have this same address for them to talk to each other. If you want security you can connect any of the 8 pins to 5V to make it high. It encodes the 12 bit parallel data into serial for transmission through an RF transmitter.

The Encoded 12 bit output data can be obtained from this pin. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. Transmission enable; active low.

HT12E Datasheet

These four pins are used to send data, the data encoded here will be decoded on HT12D IC sharing the same address bits. SPI Module of Arduino. The IC is has a wide range of operating voltage from 2. This oscillator can be used by connecting these two pins through a 1M Resistor. This data should be sent to the HT12D for decoding, it can either be sent directly through a wire or by using a wireless medium dagasheet RF or IR.

Categories:

Leave a Comment